Scroll to top

What Is a Pick and Carry Crane?

Most mobile cranes stop and set up on outriggers before they lift. A pick and carry crane takes the load straight onto its tyres and drives with it. This guide sets out how it works and what to check before one arrives.

Overview

What is a pick and carry crane?

A pick and carry crane is a mobile crane that lifts on its own wheels, with no outriggers to set up, and can drive with the load hanging from the hook. It can lift a machine and carry it across a factory floor to its new position, in spaces too tight for a crane on outriggers.

In short

  • With no outriggers, the whole weight of crane and load goes down through the wheels into the floor.
  • With the boom fully out, capacity can fall to a small fraction of the headline figure.
  • Among the makers named here, ranges run from Valla’s 1.8 t 18E up to Ormig’s 100 t 100iE.
  • Operators can train for them under endorsements in the CPCS Mobile Crane (A60) and Compact Crane (A66) categories.

We own four electric pick and carry cranes, from 5 t to 12 t, and supply them through our electric pick and carry crane hire service. Each one has its spec sheet and load charts in our crane library. We also supply larger pick and carry cranes above 12 t.

How it works

How a pick and carry crane lifts and moves

A conventional mobile crane stands on outriggers to keep it steady while it lifts, as the guide to the parts of a mobile crane shows. A pick and carry crane is built to work without them.

Lifting on its wheels

The crane balances the load against its own weight and its counterweight, which on larger models is made up of removable sections. With nothing to set up, it can start lifting as soon as it is in position, and it takes up far less floor space than a crane standing on outriggers.

Travelling with the load

Once the load is clear of the floor, the crane drives with it to where it has to go. One machine then lifts and places the load, where otherwise it might pass from a crane to skates or a forklift. The code of practice for the safe use of mobile cranes is BS 7121-3, and what it recommends is explained in a separate guide to BS 7121-3.

Capacity and the load chart

Every pick and carry crane has a load chart giving its capacity at each boom length and angle. The headline figure applies only with the boom close in. On the chart for our Valla 75E, 7.5 t close to the crane falls to 0.9 t with the boom fully out and level. How to read a crane load chart explains the rest of the chart.

Electric

Electric pick and carry cranes for indoor work

Pick and carry cranes are built with battery or engine power. Valla, now part of Tadano, builds its current range as electric cranes, and Franna, a Terex brand, builds articulated pick and carry cranes that drive between jobs on the road. The compact electric models are the ones built for factory floors, and they are the cranes we own.

Battery power

Battery power means no exhaust fumes inside the building. Valla describes its electric cranes as built for indoor and sensitive sites where emissions and noise must be kept to a minimum, which matters on food sites and anywhere staff keep working close to the lift.

Non-marking tyres

All four of the pick and carry cranes we supply run on non-marking tyres, according to their spec sheets, so they can cross finished and painted floors without leaving tyre marks.

Size and steering

Our electric cranes measure 1.40 m to 2.21 m wide and steer on their rear wheels. The Valla 50E has a turning radius of 2.75 m, and the Ormig 10tmE comes down to 2.17 m high with its light removed.

Crane Capacity Max hook height Max reach Width Height
Valla 50E 5 t 7.2 m 4.82 m 1.40 m 2.07 m
Valla 75E 7.5 t 7.5 m, or 7.8 m with fly jib 5.35 m, or 6.13 m with fly jib 1.74 m 2.29 m
Ormig 10tmE 10 t 9.7 m, or 11.8 m with fly jib 6.33 m, or 8.5 m with fly jib 2.21 m 2.46 m
Valla 120E 12 t 7.5 m, or 10.1 m with fly jib 4.1 m, or 7.1 m with fly jib 2.10 m 2.32 m

Capacities are the maximum, with the boom close in. The Ormig 10tmE takes up to 3 t on its fly jib. Reach is measured from the centre of the front wheel on the Valla cranes and from the front of the front tyre on the Ormig. Figures come from our spec sheets for the Valla and Ormig cranes we supply. Check the load chart on each crane’s page for the capacity at the radius you need.

Uses

What pick and carry cranes are used for

Our electric pick and carry cranes work where a load has to be lifted and moved under a low roof or between machines.

  • Machinery installation: lifting new machines off the delivery vehicle and onto their bases, as part of our machine delivery and installation service.
  • Moving machines within a site: shifting equipment from one bay to another for a new layout, through our machine movement service.
  • Plant maintenance: lifting motors and gearboxes out for repair and back in again.
  • Factory moves: loading and unloading machines at both ends of a relocation. The wider move is planned as How to plan a factory relocation describes.
  • Confined spaces: plant rooms, and gaps between live production lines.
Yellow Ormig electric pick and carry crane with its boom raised, parked outside an industrial unit
An Ormig electric pick and carry crane.

Planning

What to check before a pick and carry lift

A pick and carry lift is planned like any other crane lift, with four checks made on site or from drawings before the crane arrives.

Floor loading

The crane’s own weight and the load both go down through its wheels, with no outriggers or mats to spread them. Our Valla 120E weighs 13.2 t before it lifts anything, and the wheel loads are always worked out from the data for the actual crane on the job. The floor along the whole route has to carry those wheel loads, including over trenches and suspended slabs. On a contract lift we supply the crane’s wheel loads and ground bearing pressure calculations, and the site’s own competent person confirms the floor and route can carry them. Our guide to crane site preparation sets out how a floor is checked.

Reach

A load placed over an obstruction or at the back of a machine bed needs reach, and reach can call for a bigger crane than the weight alone. What size crane do I need? shows how radius and capacity work together.

The travel route

The crane needs a firm, level route from the entrance to the lift, clear of obstructions. Ramps and uneven floors have to be checked against the maker’s limits for that crane, so the route gets the same planning as the lift itself.

Doors and headroom

Door openings and headroom need measuring, along with any pipework and cable trays overhead, both for the crane getting in and for the boom rising during the lift.

Hiring

Hiring a pick and carry crane or booking a contract lift

We supply our pick and carry cranes on short and long term hire, with one of our operators, who hold CPCS or NPORS cards, or without an operator if you have your own. We can also carry out the whole job as a contract lift, planned to BS 7121.

In Great Britain, regulation 8 of LOLER puts the duty on the employer to make sure each lift with a pick and carry crane is properly planned by a competent person, appropriately supervised and carried out in a safe manner. What the regulations ask for is set out in our LOLER guide.

Crane hire or contract lift

On crane hire, you take the crane, with or without our operator, and plan and run the lift yourself. On a contract lift, our appointed person draws up the lift plan, in house, and our crew carries out the lift. Who is responsible for what is compared in Crane hire or contract lift: what is the difference?.

What we need to know

  • The weight and size of the load, and where its lifting points are
  • How far it travels, and the reach at which it is set down
  • The route from the entrance, with door sizes and headroom
  • The floor construction along the route

Questions

Common questions

No. A pick and carry crane balances the load against its own weight and its counterweight, so there are no outriggers to set up. That lets it travel with the load on the hook, within the limits the maker sets for travelling with a load, and work in a bay or plant room where outriggers would not fit.

Yes, electric pick and carry cranes are built for it. They run on batteries with no exhaust fumes, and the Valla 120E comes with non-marking tyres, so they can work inside factories and plant rooms. The floor still has to carry the crane’s wheel loads, and the doors and headroom have to be big enough to let it in.

It depends on the model and the reach. Valla lists models from 1.8 t to 50 t and Ormig goes up to 100 t, while our own electric cranes lift 5 t to 12 t at their shortest reach. Capacity falls as the boom reaches out, so every lift is checked against the load chart for the actual crane.

In Great Britain, regulation 9 of PUWER requires employers to make sure anyone using work equipment has received adequate health and safety training. In the CPCS scheme, Mobile Crane (A60) has a pick and carry duties endorsement, and Compact Crane (A66) has endorsements for mobile industrial and 360 pick and carry cranes. Our operators hold CPCS or NPORS cards.

Not quite. Spider cranes, also called mini cranes, set up on fold-out outriggers before they lift. A pick and carry crane has no outriggers and can drive with the load on the hook. If a quote says mini crane, check which kind of crane it means.

Franna is a Terex brand of pick and carry crane built on a frame hinged in the middle, which Terex calls articulated, and it lifts without outriggers. Franna cranes drive between jobs at road speed. Terex describes its Franna AT 22 as a popular choice in the Australian crane market, used on mining and construction projects.

Get a quote

Get a quote for pick and carry crane hire

Call us on 0800 008 6096 or email office@synergy-lifting.co.uk with the weight of the load and the route it has to take, and we will recommend a crane and quote for the lift.

Find out more about our electric pick and carry crane hire and machine movement services. For a contract lift, see our crane hire and contract lifting page.

Related

Find out more

Get a quote

Ready for a quote?

Send us the details and we will come back with a quote, usually the same day for a desktop survey.

Get a quote

Or call 0800 008 6096

  • Amazon
  • Brotje
  • ITV Studios
  • NG Bailey
  • Northern Structures
  • Schneider Electric
  • Spaans Babcock
  • Sulzer
  • Wates

This guide is general information, not legal or professional advice. Check the current law and take advice on your own situation before acting on it.

Peter Stephens
Written by Peter Stephens
Peter Stephens is Managing Director of Synergy Lifting Ltd, the family-run crane hire, contract lifting and machine movement company. He leads the commercial side of the business, including quoting and planning projects with clients.