City crane
Kato CR-250Rv
The Kato CR-250Rv is a 25 tonne, two axle city crane with a 29m main boom, supplied with an operator for crane hire or as part of a contract lift.
Spec sheet
Download the Kato CR-250Rv spec sheet
Kato CR-250Rv
Download the manufacturer’s specification sheet (PDF · 16 pages · 3.0MB).
Key figures
Kato CR-250Rv key figures
- Maximum capacity
- 25 tonnesAt 2.8m on the 6.7m boom
- Main boom
- 6.7m to 29m6-section
- Jib
- 5.3m to 8.2m2-section, hydraulically telescopic
- Maximum hook height
- 38.4mOn the jib; 30m on the boom
- Carrier width
- 2.395mOverall width
- Axle lines
- 2
Specification
Kato CR-250Rv specification
| Item | Specification |
|---|---|
| Manufacturer | Kato Works |
| Model | CR-250Rv |
| Type | City crane |
| Maximum capacity | 25 tonnes at 2.8m on the 6.7m boom (7 parts of line, via the rooster sheave per the chart notes); 7 tonnes at 7m on the 29m boom; 7.5 tonnes on the optional searcher hook; rooster sheave up to 4 tonnes; stationary on rubber and pick and carry (below 2km/h) duties also charted |
| Main boom | 6.7m to 29m, round-shaped 6-section hydraulically telescopic |
| Boom angle | -9 to 84 degrees |
| Maximum hook height | 30m on the boom, 38.4m on the jib (maximum rated lifting height) |
| Jib | 2-section hydraulically telescopic fly jib, 5.3m to 8.2m, hydraulic stepless offset 7 to 60 degrees; 3 tonnes on the 5.3m jib, 2.3 tonnes on the 8.2m jib |
| Weight and axle loads | Gross vehicle weight approx. 23,795kg; front axle approx. 11,895kg, rear axle approx. 11,900kg (without optional equipment) |
| Outriggers | Hydraulic H-beam; extension width 6m fully extended, 5.2m, 4.4m and 3.4m intermediate, 2.085m retracted |
| Axle lines | 2, planetary drive/steer axles (reverse Elliot type); switchable 4×2 or 4×4; front, coordinated, crab and rear steering; minimum turning radius 8.3m (2 wheel steer), 5m (4 wheel steer) |
| Tyres and width | 385/95 R25; overall width 2,395mm |
| Suspension | Hydro-pneumatic, hydraulic locking with suspension cylinder, front and rear |
| Engine | Cummins B6.7 (EU Stage V) 6-cylinder turbo diesel with intercooling, 209kW at 2,000rpm, 1,152Nm at 1,500rpm |
| Transmission | Remote mounted full automatic, 4 forward and 1 reverse with high-low selector, torque converter with lock-up clutch |
| Control and safety | ACS (Automatic Crane System) with voice alarm, slewing automatic stop, boom raise, lower and extension dampening, working range limit mode, outrigger status detector, overhoist prevention device |
Specifications are taken from the manufacturer published specification sheet for this model and are given as a guide only. Machines vary by build, options and configuration, and figures can change without notice. Nothing on this page forms part of a contract or a lift plan: the crane, its configuration and its load chart are confirmed when we quote and plan your lift.
Compare
Kato CR-250Rv compared with similar cranes
| This craneKato CR-250Rv | Kato CR-200Rf | Terex Demag AC 30 City | Kato CR-130Rf | |
|---|---|---|---|---|
| Maximum capacity | 25 tonnes | 20 tonnes | 30 tonnes | 13 tonnes |
| Main boom | 6.7m to 29m | 6.5m to 28m | 7.5m to 25m | 5.3m to 24m |
| Swingaway jib | Not stated | Not stated | 7.1m or 13m | Not stated |
| Jib | 5.3m to 8.2m | 4m to 5.8m | Not stated | 3.6m to 5.5m |
| Maximum tip height | Not stated | Not stated | 40m | Not stated |
| Maximum hook height | 38.4m | 34.8m | Not stated | 30.3m |
| Counterweight | Not stated | Not stated | 2.3 tonnes | Not stated |
| Carrier width | 2.395m | 2.29m | Not stated | 1.995m |
| Axle lines | 2 | 2 | 2 | 2 |
Related
Find out more
Get a quote
Ready for a quote?
Send us the details and we will come back with a quote, usually the same day for a desktop survey.
Or call 0800 008 6096
